Specification

2 loose body flanges revolving around 2 coupling ends (butt weld, threaded…)

Use

With 4, 6 or 8 holes their bolts ensure the characteristic tightness of the body-coupling ends sub-assembly on the 3-piece valve.

Even easier to install

Valve assembly is done without lining up the connectors beforehand.
It is ideally used in pre-assembly (e.g. in the workshop):

The question of positioning only arises at the end, and so is never a limiting factor or an obstacle in preparing the "pipe assemblies". This feature makes preparation work in the engineering department a lot easier.

Full seal guarantee

Misalignment results in torque settings that affect the seal because the "valve-piping-couplings" assembly is then subject to stress.
This risk disappears when using loose flanges.

Quicker assembly time

Using the loose flange system coupled together with those in the kit allows fitters and maintenance workers to cut assembly time by approximately 30%.
Examples backed up by figures support this information.

Complete positional freedom

You may decide, or may be forced over time, to free a required amount of space.
This is not a problem, simply undo the bolts to free the valve rotation area (body only) or even the motorized assembly (body-actuator) and position them as required over a 360° area around the pipes.

Specification

A packing system made up of a case and a cover (in recyclable polystyrene), as well as a colour-coded, cardboard sheath (red for stainless steel, blue for carbon steel).

Use

Valve storage and delivery

Even more uses

The packaging allows greater flexibility, both in the choice of connection (e.g. one side welded, one side screwed) and the choice of bore (e.g. one side with full bore, one side with reduced bore), or even in the choice of material (e.g. one side in stainless steel, one side in carbon steel).

This same packaging is used in our check valve, filter and sight glass range with the same connecting ends!

A cost-efficient solution

No risk of extra costs when mixing your choices as described above.

Quicker assembly time: in the case of weld valves, there is no more need to "dismantle" the valves before welding. Subject to use.
Using the Kit system with the loose flanges allows fitters and maintenance workers to cut the valve assembly time by approximately 30%!

No additional maintenance costs: no more need to order a complete valve (e.g. weld valves when only the body needs replacing) for maintenance work - we deliver the body unit separately without the additional costs associated with spare parts!

Streamline your stocks: no more need to keep full versions of every version in stock… just stock the various body diameters on the one hand and your usual couplings on the other hand, and simply complete the Kit at your convenience!

Total safety

From storage to on-site installation, the Kit ensures maximum safety:

Storage and transport: the valve is under optimum storage conditions, protected against dust, light or knocks from other objects.

Installation: sealing items (seats and seals) given maximum protection up until the body is fitted. As the body is protected by the Kit, it is never deposited on the ground without its protective ends and so never weakened. Consequently, there is no risk of marking or leakage.
In the same way, any risk of losing internal parts is eliminated.

If there is any doubt, the assembly instructions and the spare parts coding are on the Kit case sheathing, thereby making assembly straightforward and risk-free.

Specification

Manufactured in stainless steel, they can be straight (full bore) or cone-shaped (reduced bore, venturi or conventional).

Use

Connecting the valve to piping, to a tank…

A larger manufacturing choice

Whether they are standard or according to a blueprint, we can manufacture any type of connector to match your needs or limitations:
e.g. BW, SW, BSP "P", NPT, CLAMP, COMPRESSION FITTINGS, TANK BOTTOM…

Faster dispatch time

As they are fully machined by our lathes, our delivery times are shorter. We can deliver very high quantities of connectors (by trays) in extremely short times for large projects, allowing our customers to start pre-assembly installation immediately.

A competitive solution

Our overall production expertise makes us more competitive, particularly for exceptional assignments (materials…)

Manufactured according to your specific requirements

Whatever the nature of your demand, we can manufacture body connectors according to your specifications, including special levels of roughness (e.g. 0.6µm), internal diameters reamed again to the ball diameter, specific tube diameters (Schedule, SMS, metric, DIN, imperial…).